Recent #INFOSWMM Twitter Postings


NRCS Dimensionless and Triangular UH in #INFOSWMM and the location of the Lag Time of Concentration in the Output http://t.co/pxbQqAU2tU
 3    
1/ #INFOSWMM in Spanish - InfoSWMM #SUSTAIN opening dialog h/t @InnovyzeDavid http://t.co/2ZPZWbjrPs
 2    
3/ #INFOSWMM in Italian - InfoSWMM #SUSTAIN Optimization http://t.co/O501iYL7N2
 2    
4/ @Innovyze has free University Student Editions SE for #INFOSURGE #INFOWATER and #INFOSWMM http://t.co/lvTOa7ZI92 http://t.co/Fz8HP1hKBz
 2    
1/ @Innovyze has free University Student Editions SE for #INFOSURGE #INFOWATER and #INFOSWMM http://t.co/lvTOa7ZI92 http://t.co/ELCIc3Ym2Y
 2    
H2S and Sulphide can be simulated in #INFOSEWER, #INFOSWMM and #INFOWORKS_ICM from @Innovyze http://t.co/8PUxYYA9YB
 2    
4/ #INFOSWMM in Spanish - InfoSWMM #SUSTAIN # Modeling LID Selection http://t.co/wHF2mnl4He
 1    
Visit Innovyze (Booth #1756) at WEFTEC 2015 and Learn about #INFOSWMM #SUSTAIN http://t.co/Jdyi0i3B1I
 1    
Visit Innovyze (Booth #1756) at WEFTEC 2015 and Learn about #INFOSWMM #SFEM http://t.co/02vGCXVv33
 1    
#INFOSWMM Fow unit you define in the simulation options (1) apply to Rules (2), Curves (3) Flow Time Series (4) http://t.co/iTl8UerIaQ
 1    
2/ @Innovyze has free University Student Editions SE for #INFOSURGE #INFOWATER and #INFOSWMM http://t.co/lvTOa7ZI92 http://t.co/J9xqehgdOx
 1    
2 #INFOSWMM in Spanish - InfoSWMM #SUSTAIN #GREEN Modeling http://t.co/VIHAZhoGya
 1    
3/ #INFOSWMM in Spanish - InfoSWMM #SUSTAIN # Modeling LID Optimization http://t.co/Cq6Et2uirc
 1    
3/ @Innovyze has free University Student Editions SE for #INFOSURGE #INFOWATER and #INFOSWMM http://t.co/lvTOa7ZI92 http://t.co/0tqEo1Zd2L
 1    
5/ #INFOSWMM in Spanish - InfoSWMM #SUSTAIN # Modeling Site Manager http://t.co/j3qjt5A2QX
 1    
6/ #INFOSWMM in Spanish - InfoSWMM #SUSTAIN # Modeling LID Optimization Goals http://t.co/u0MoikMxhG
 1    
1/ #INFOSWMM in Italian - InfoSWMM #SUSTAIN opening dialog h/t @InnovyzeLuca http://t.co/IxIi10LUDg
 1    
2/ #INFOSWMM in Italian - InfoSWMM #SUSTAIN Siting Manager http://t.co/JMxU0vLpJH
 1    
#INFOSWMM Direct Pump Rule (1) constant pump rate, (2) pump setting based on a time series and (3) use a RTC setting http://t.co/K5XJvDL1i9
 1    
H2S and Sulphide can be simulated in #INFOSEWER, #INFOSWMM and #INFOWORKS_ICM from @Innovyze #rt http://t.co/HfQ3knfz2x
 0    

Comments

Post a Comment

Popular posts from this blog

SWMM 5 Error Messages

Engine Error Number Description ERROR 101: memory allocation error.                                                                                             ERROR 103: cannot solve KW equations for Link                                                                                   ERROR 105: cannot open ODE solver.                                                                                              ERROR 107: cannot compute a valid time step.                                                                                     ERROR 108: ambiguous outlet ID name for Subcatchment                                                                            ERROR 109: invalid parameter values for Aquifer                                                                                  ERROR 110: ground elevation is below water table for Subcatchment                                                         
Read more

Orifice and Weir flow calculations

Note: Orifice and Weir Flow Computations The orifice flow calculation proceeds as follows: 1. Initially and whenever the setting (i.e., the fraction opened) changes, flow coefficients for both orifice and weir behavior are computed as follows: a. For side orifices: Define Hcrit = h/2 where h is the opening height. b. For bottom orifices: i. For a circular orifice, compute area over length (i.e., circumference) as AL = h /4. ii. For a rectangular orifice compute AL = h*w/(2*(h+w)) where w is the opening width. iii. Compute Hcrit = Cd*AL/0.414 where Cd is the orifice discharge coefficient. At step 1b, the critical head for the bottom orifice, where orifice flow turns into weir flow, is found by equating the result of the orifice equation to that of the weir equation Cd*Area*sqrt(2g)*sqrt(Hcrit) = Cw*Length*sqrt(Hcrit)*Hcrit or Hcrit = (Cd * Area) / (Cw/sqrt(2g) * Length) The value of Cw/sqrt(2g) for a sharp crested weir is 0.414.
Read more

EMC Washoff in SWMM5

Image
There are four steps to using EMC concentrations in your network: 1. Define your pollutant by adding a pollutant using the Data=>Quality=>Pollutant command : 2. Define the Land Use by using the Data=>Land Uses command or the Land Use Editor: 3. Define Buildup to be None by clicking on the None Tab: 4. Define the EMC Washoff concentration by clicking on the Washoff Tab: This is where you would add a GW concentration More: http://www.swmm2000.com/
Read more