SWMM5 Table by Object Shows a Tabular view of the Important Results Varables

You can see many important SWMM 5 object result variables if you use the Table by Object Output Tool.  An example would be if you want to see the results of the groundwater, infiltration and surface runoff versus the rainfall over time in one view.  It is also easy to copy and paste to Excel if you need to collect the results.

SWMM 5 Table Tool

SWMM 5 Table Tool Output
                     2 Rainfall         Total Losses     Runoff           GW Flow          GW Elev.         Evap             Depth           
Days       Hours      (mm/hr)          (mm/hr)          (LPS)            (LPS)            (m)              (mm/hr)          (mm)            
0 0:05:00 0 0 0 43.93 9.99 0 0
0 0:10:00 0 0 0 43.87 9.98 0 0
0 0:15:00 0 0 0 43.8 9.97 0 0
0 0:20:00 0 0 0 43.73 9.97 0 0
0 0:25:00 0 0 0 43.67 9.96 0 0
0 0:30:00 0 0 0 43.6 9.95 0 0
0 0:35:00 0 0 0 43.54 9.95 0 0
0 0:40:00 0 0 0 43.47 9.94 0 0
0 0:45:00 0 0 0 43.41 9.93 0 0
0 0:50:00 0 0 0 43.34 9.93 0 0
0 0:55:00 0 0 0 43.28 9.92 0 0
0 1:00:00 0 0 0 43.21 9.91 0 0
0 1:05:00 0 0 0 43.15 9.91 0 0
0 1:10:00 0 0 0 43.08 9.9 0 0

Comments

Post a Comment

Popular posts from this blog

Orifice and Weir flow calculations

Note: Orifice and Weir Flow Computations The orifice flow calculation proceeds as follows: 1. Initially and whenever the setting (i.e., the fraction opened) changes, flow coefficients for both orifice and weir behavior are computed as follows: a. For side orifices: Define Hcrit = h/2 where h is the opening height. b. For bottom orifices: i. For a circular orifice, compute area over length (i.e., circumference) as AL = h /4. ii. For a rectangular orifice compute AL = h*w/(2*(h+w)) where w is the opening width. iii. Compute Hcrit = Cd*AL/0.414 where Cd is the orifice discharge coefficient. At step 1b, the critical head for the bottom orifice, where orifice flow turns into weir flow, is found by equating the result of the orifice equation to that of the weir equation Cd*Area*sqrt(2g)*sqrt(Hcrit) = Cw*Length*sqrt(Hcrit)*Hcrit or Hcrit = (Cd * Area) / (Cw/sqrt(2g) * Length) The value of Cw/sqrt(2g) for a sharp crested weir is 0.414.
Read more

SWMM 5 Error Messages

Engine Error Number Description ERROR 101: memory allocation error.                                                                                             ERROR 103: cannot solve KW equations for Link                                                                                   ERROR 105: cannot open ODE solver.                                                                                              ERROR 107: cannot compute a valid time step.                                                                                     ERROR 108: ambiguous outlet ID name for Subcatchment                                                                            ERROR 109: invalid parameter values for Aquifer                                                                                  ERROR 110: ground elevation is below water table for Subcatchment                                                         
Read more

EMC Washoff in SWMM5

Image
There are four steps to using EMC concentrations in your network: 1. Define your pollutant by adding a pollutant using the Data=>Quality=>Pollutant command : 2. Define the Land Use by using the Data=>Land Uses command or the Land Use Editor: 3. Define Buildup to be None by clicking on the None Tab: 4. Define the EMC Washoff concentration by clicking on the Washoff Tab: This is where you would add a GW concentration More: http://www.swmm2000.com/
Read more