What Node and Link Invert Elevations Does SWMM 5 Use?

Note:  What Node and  Link Invert Elevations Does SWMM 5 Use?

SWMM 5 uses the following Node information from the user:
·         Node Invert Elevation,
·         The Node Rim Elevation which is the Node Invert Elevation + the Maximum node depth
·         The Ponded Area when the Ponded  Area option is used
·         The Surcharge Depth above the Node Rim Elevation

SWMM 5 uses the following link information from the user:
·         The Link Upstream Offset Depth or Offset Elevation and
·         The Link Downstream Offset Depth or Offset Elevation
·         The Link Maximum Depth or Diameter

SWMM 5 calculates the following information internally:
·         The Pipe Crown Elevation at the upstream and downstream link nodes.  The Pipe Crown is the Pipe Diameter + Link Offsets
·         The Node Highest Pipe Crown Elevation,  the new rim elevation will be used in the program
·         The Surcharge Depth above the Rim Elevation if the Node has a Surcharge Pressure Depth at the Node during the simulation,
o   If the Surcharge Depth is 0 then the program will either lose the flooded water or store the flooded water during the simulation
·         The Flooded Depth above the  Rim Elevation if the Node uses the Ponded Area Option
o   You have to enter a Ponded Area for the node AND use the Global Allow Ponding Option

SWMM 5 Rules for Pipes
·         The Pipe Invert Cannot be below either upstream or downstream node invert – the program will print a warning in the rpt file and set the offset to 0 internally,
·         The Pipe Crown Cannot be above the Rim Elevation of the Node – the program will raise the Rim Elevation when this happens and print a warning in the rpt file.

The use of Offset Depth or Offset Elevation for the Link Offsets is based on the user choice at the bottom of the SWMM 5 GUI Map.

Or in the Tools/Preference/Operation dialog of InfoSWMM/H20MAP SWMM 




Comments

Post a Comment

Popular posts from this blog

Orifice and Weir flow calculations

Note: Orifice and Weir Flow Computations The orifice flow calculation proceeds as follows: 1. Initially and whenever the setting (i.e., the fraction opened) changes, flow coefficients for both orifice and weir behavior are computed as follows: a. For side orifices: Define Hcrit = h/2 where h is the opening height. b. For bottom orifices: i. For a circular orifice, compute area over length (i.e., circumference) as AL = h /4. ii. For a rectangular orifice compute AL = h*w/(2*(h+w)) where w is the opening width. iii. Compute Hcrit = Cd*AL/0.414 where Cd is the orifice discharge coefficient. At step 1b, the critical head for the bottom orifice, where orifice flow turns into weir flow, is found by equating the result of the orifice equation to that of the weir equation Cd*Area*sqrt(2g)*sqrt(Hcrit) = Cw*Length*sqrt(Hcrit)*Hcrit or Hcrit = (Cd * Area) / (Cw/sqrt(2g) * Length) The value of Cw/sqrt(2g) for a sharp crested weir is 0.414.
Read more

SWMM 5 Error Messages

Engine Error Number Description ERROR 101: memory allocation error.                                                                                             ERROR 103: cannot solve KW equations for Link                                                                                   ERROR 105: cannot open ODE solver.                                                                                              ERROR 107: cannot compute a valid time step.                                                                                     ERROR 108: ambiguous outlet ID name for Subcatchment                                                                            ERROR 109: invalid parameter values for Aquifer                                                                                  ERROR 110: ground elevation is below water table for Subcatchment                                                         
Read more

EMC Washoff in SWMM5

Image
There are four steps to using EMC concentrations in your network: 1. Define your pollutant by adding a pollutant using the Data=>Quality=>Pollutant command : 2. Define the Land Use by using the Data=>Land Uses command or the Land Use Editor: 3. Define Buildup to be None by clicking on the None Tab: 4. Define the EMC Washoff concentration by clicking on the Washoff Tab: This is where you would add a GW concentration More: http://www.swmm2000.com/
Read more