Arc Map If Statements for Showing Flooding in InfoSWMM

Arc Map If Statements for Showing Flooding in InfoSWMM

Arc Map If Statements for Showing Flooding in InfoSWMM

by dickinsonre
Arc Map If Statements for Showing Flooding in InfoSWMM

You can use a combination of the Map Display in InfoSWMM and the Arc Map Label Properties to show the Maximum Ponded Volume at a node during amInfoSWMM simulation. 

The label function in VBSCRIPT to show just non zero flooded volumes(Figure 1) is:

Function FindLabel ( [PONDED_VOL] )
If [PONDED_VOL] > 0 THEN
  FindLabel = "" & FormatNumber([PONDED_VOL],2) & ""
END IF
End Function

and the values of Flooded Time,  Maximum Flooded Rate and Maximum Ponded Volume can be found in the Junction Attribute Table(Figure 2)  but not the Junction Summary Table of the InfoSWMM output report manager tables. 

A VBSCRIPT function to show both ponded volume and flooded rate (Figure 3) is:

Function FindLabel ( [PONDED_VOL], [FLOOD_RATE]  )
If [PONDED_VOL] > 0 THEN
  FindLabel = "" & FormatNumber([PONDED_VOL],2) & " / "   & FormatNumber([FLOOD_RATE],1)
END IF
End Function



Figure 1.  InfoSWMM Map Display of Ponded Volume which is the integral of node flooding over the flooded time.

Figure 2.   If you use the Map Display feature in InfoSWMM then the total flooded time, flood rate and maximum ponded volume will be shown in the Junction Attribute Table.


Figure 3.  Labels showing both Maximum Flooded Volume and Maximum Flooded Time on the InfoSWMM Map Display








Comments

Post a Comment

Popular posts from this blog

Orifice and Weir flow calculations

Note: Orifice and Weir Flow Computations The orifice flow calculation proceeds as follows: 1. Initially and whenever the setting (i.e., the fraction opened) changes, flow coefficients for both orifice and weir behavior are computed as follows: a. For side orifices: Define Hcrit = h/2 where h is the opening height. b. For bottom orifices: i. For a circular orifice, compute area over length (i.e., circumference) as AL = h /4. ii. For a rectangular orifice compute AL = h*w/(2*(h+w)) where w is the opening width. iii. Compute Hcrit = Cd*AL/0.414 where Cd is the orifice discharge coefficient. At step 1b, the critical head for the bottom orifice, where orifice flow turns into weir flow, is found by equating the result of the orifice equation to that of the weir equation Cd*Area*sqrt(2g)*sqrt(Hcrit) = Cw*Length*sqrt(Hcrit)*Hcrit or Hcrit = (Cd * Area) / (Cw/sqrt(2g) * Length) The value of Cw/sqrt(2g) for a sharp crested weir is 0.414.
Read more

SWMM 5 Error Messages

Engine Error Number Description ERROR 101: memory allocation error.                                                                                             ERROR 103: cannot solve KW equations for Link                                                                                   ERROR 105: cannot open ODE solver.                                                                                              ERROR 107: cannot compute a valid time step.                                                                                     ERROR 108: ambiguous outlet ID name for Subcatchment                                                                            ERROR 109: invalid parameter values for Aquifer                                                                                  ERROR 110: ground elevation is below water table for Subcatchment                                                         
Read more

EMC Washoff in SWMM5

Image
There are four steps to using EMC concentrations in your network: 1. Define your pollutant by adding a pollutant using the Data=>Quality=>Pollutant command : 2. Define the Land Use by using the Data=>Land Uses command or the Land Use Editor: 3. Define Buildup to be None by clicking on the None Tab: 4. Define the EMC Washoff concentration by clicking on the Washoff Tab: This is where you would add a GW concentration More: http://www.swmm2000.com/
Read more