InfoSWMM Version 12 Revs Up Modeling Performance With HEC-22 and 64-Bit Support



InfoSWMM Version 12 Revs Up Modeling Performance With HEC-22 and 64-Bit Support
Latest Software Release Supports Faster Time to Design and Lower Analysis Costs
Broomfield, Colorado USA, July 25, 2012 — In its ongoing quest to equip the wastewater industry with the world’s most comprehensive and innovative smart network modeling and management solutions, Innovyze, a leading global innovator of business analytics software and technologies for wet infrastructure, today announced the worldwide availability of the V12 Generation of its industry-leading InfoSWMM for ArcGIS (Esri, Redlands, CA). InfoSWMM V12 enables engineers to work more efficiently and reliably with very large and complex network models, thanks to improvements in such areas as HEC-22 inlet support, built-in 64-bit simulation, enhanced water quality modeling, and batch run scenario management that will positively impact modeling teams each and every day.
The only urban drainage modeling solution certified by the National Association of GIS-centric Software, the full-featured InfoSWMM analysis and design program delivers the highest rate of return in the industry. All operations of a typical sewer system — from analysis and design to management functions such as water quality assessment, pollution prediction, sediment transport and deposition, urban flooding, real-time control, and record keeping — are addressed in a single, fully integrated geoengineering environment. The program’s powerful hydraulic and water quality computational engine is based on the current SWMM 5 version, which is endorsed by the USEPA and certified by FEMA. These features and more result in an enhanced modeling experience and greater realism of displayed results — advantages that translate to increased productivity, reduced costs, higher accuracy, better efficiency, and improved designs.
InfoSWMM also serves as a robust base platform for advanced modeling, operational, capital planning, and analytics-driven asset management extensions. Some of these critical applications include InfoSWMM 2D (two-dimensional surface flood modeling), CapPlan (risk-based capital planning and asset performance modeling),InfoMaster (GIS-centric asset management), and RDII Analyst (rainfall-dependent inflow and infiltration planning and analysis).
The release of InfoSWMM V12 extends previous generations’ capabilities with significant modeling enhancements and groundbreaking innovations in geoengineering productivity and efficiency. These improvements greatly simplify, accelerate, and integrate urban drainage network engineering, helping wastewater engineers develop better designs and operational improvements faster. Key new built-in modeling and computational tools include:

  • ability to explicitly model five HEC-22 inlet types connecting overland and underground systems (continuous grate inlet, continuous curb-opening inlet, sag grate inlet, sag curb-opening inlet and sag combination inlet),
  • complete 64-bit functionality resulting in faster simulation runs,
  • enhanced hydrogen sulfide and corrosion modeling,
  • flexibility in run time scheduling, 
  • direct control of the number of dynamic solution threads or cores for parallel processing, and
  • ability to run multiple scenarios in batch mode at one time or to schedule the model runs at future times.

“Our priorities have always been to advance the frontiers of smart network modeling technology and support our customers’ successes by helping them be more productive and competitive,” said Paul F. Boulos, Ph.D., BCEEM, Hon.D.WRE, Dist.D.NE, F.ASCE, President and Chief Operating Officer of Innovyze. “This major InfoSWMMrelease delivers on our promise to equip our customers with the ultimate ArcGIS-centric decision support tool for sewer collection and urban drainage systems. Like its predecessors, InfoSWMM V12 sets a new standard for quality and high-performance network modeling and management with unrivaled power, cutting-edge capabilities, rich functionality, and ease of use. From top to bottom, this release is designed for record modeling performance that enables users to increase their productivity and quality while achieving their engineering and business goals.”

Comments

Post a Comment

Popular posts from this blog

Orifice and Weir flow calculations

Note: Orifice and Weir Flow Computations The orifice flow calculation proceeds as follows: 1. Initially and whenever the setting (i.e., the fraction opened) changes, flow coefficients for both orifice and weir behavior are computed as follows: a. For side orifices: Define Hcrit = h/2 where h is the opening height. b. For bottom orifices: i. For a circular orifice, compute area over length (i.e., circumference) as AL = h /4. ii. For a rectangular orifice compute AL = h*w/(2*(h+w)) where w is the opening width. iii. Compute Hcrit = Cd*AL/0.414 where Cd is the orifice discharge coefficient. At step 1b, the critical head for the bottom orifice, where orifice flow turns into weir flow, is found by equating the result of the orifice equation to that of the weir equation Cd*Area*sqrt(2g)*sqrt(Hcrit) = Cw*Length*sqrt(Hcrit)*Hcrit or Hcrit = (Cd * Area) / (Cw/sqrt(2g) * Length) The value of Cw/sqrt(2g) for a sharp crested weir is 0.414.
Read more

SWMM 5 Error Messages

Engine Error Number Description ERROR 101: memory allocation error.                                                                                             ERROR 103: cannot solve KW equations for Link                                                                                   ERROR 105: cannot open ODE solver.                                                                                              ERROR 107: cannot compute a valid time step.                                                                                     ERROR 108: ambiguous outlet ID name for Subcatchment                                                                            ERROR 109: invalid parameter values for Aquifer                                                                                  ERROR 110: ground elevation is below water table for Subcatchment                                                         
Read more

EMC Washoff in SWMM5

Image
There are four steps to using EMC concentrations in your network: 1. Define your pollutant by adding a pollutant using the Data=>Quality=>Pollutant command : 2. Define the Land Use by using the Data=>Land Uses command or the Land Use Editor: 3. Define Buildup to be None by clicking on the None Tab: 4. Define the EMC Washoff concentration by clicking on the Washoff Tab: This is where you would add a GW concentration More: http://www.swmm2000.com/
Read more